sensor:
 - platform: hx711
   name: "HX711 Value"
   dout_pin: D0
   clk_pin: D1
   gain: 128
   update_interval: 60s

esphome:
 name: hive2
 platform: ESP32
 board: esp-wrover-kit

wifi:
 networks:
 - ssid: "@@@@@@@@" # <== тут перечисляете все ваши wifi сети
   password: "@@@@@@@@"
 - ssid: "@@@" # <== тут перечисляете все ваши wifi сети
 manual_ip:
   static_ip: 192.168.8.52 # <== это если вы любите статические адреса ... можете убраь и адреса будут с роутера
   gateway: 192.168.8.1
   subnet: 255.255.255.0


# Enable logging
logger:

# Enable Home Assistant API
api:

ota:

status_led:
 pin: GPIO2# <== для удобства подключаем лампочку статуса
 
sensor:
 - platform: hx711
   name: "Hive scale 2_2"
   dout_pin: GPIO17 # <== укажем ноги которые вы подключили к модулю
   clk_pin: GPIO16
   gain: 128
   update_interval: 6s # <== датчик шумный поднимем частоту его опроса
   filters:
     - calibrate_linear:
         - 440066  -> 0 # <== калибровочные значения
         - 663924   -> 10
     - sliding_window_moving_average: # <== и кратно усредним скользящим средним
         window_size: 10
         send_every: 10          
   unit_of_measurement: kg
   accuracy_decimals: 2

 - platform: hx711
   name: "Hive scale 2_1"
   dout_pin: GPIO26 # <== укажем ноги которые вы подключили к модулю
   clk_pin: GPIO25
   gain: 128
   update_interval: 60s # <== этот датчик не шумит
   filters:
     - calibrate_linear:
         - 302670  -> 0 # <== калибровочные значения
         - 69367   -> 10
   unit_of_measurement: kg
   accuracy_decimals: 2

 - platform: filter
   name: "filtered realistic 2_2"
   entity_id: sensor.hive_scale_2_2
   filters:
     - filter: outlier
       window_size: 4
       radius: 4.0
     - filter: lowpass
       time_constant: 20
       precision: 3

Feature:
Internal 1000 Ohm half-bridge strain gauge load cell, range is 50kg, half-bridge structure.
When measuring, the correct force is applied to the outer side of the strain E-shaped beam portion of the sensor
(i.e., a strain gauge affixed to the middle, with a beam of white plastic cover arm)
and the outside edges to form a shear force in the opposite direction,
i.e., in the middle of strain beam bending necessary changes can occur under stress,
strain beam side by another force can not have a barrier.

Specification:
Item Type: Weighing Sensor
Weight: 0.65oz
Dimension:3.4× 3.4cm/ 1.33× 1.33inches
Capacity:50kg/110lb(each)
Structure:Half-bridge
Output Sensitivity:1.0±15%mv/V
Nonlinearity:0.05 % F.S
Input Impedance: 1000±10ohm
Output Impedance:1000±10ohm
Insulation Resistance:≧2000 M ohm

The sensor use the following three methods:
1, using a sensor with external resistors full bridge measurement range of a sensor range: 50kg. Higher requirements for external resistor
2, the use of only two full-bridge sensors measuring range is the range of the two sensors and: 50kgx2 = 100kg
3, the use of four full-bridge sensors measuring range is the range of four sensors and: 50kgx4 = 200kg